Hall circles (also known as M-circles and N-circles) are a graphical tool in control theory used to obtain values of a closed-loop transfer function from the Nyquist plot (or the Nichols plot) of the associated open-loop transfer function. Hall circles have been introduced in control theory by Albert C. Hall in his thesis.
Construction Consider a closed-loop linear control system with open-loop transfer function given by transfer function G ( s ) {\displaystyle G(s)} and with a unit gain in the feedback loop. The closed-loop transfer function is given by T ( s ) = G ( s ) 1 + G ( s ) {\textstyle T(s)={\frac {G(s)}{1+G(s)}}} . To check the stability of T(s), it is possible to use the Nyquist stability criterion with the Nyquist plot of the open-loop transfer function G(s). Note, however, that the Nyquist plot of G(s) does not give the actual values of T(s). To get this information from the G(s)-plane, Hall proposed to construct the locus of points in the G(s)-plane such that T(s) has constant magnitude and also the locus of points in the G(s)-plane such that T(s) has constant phase angle. Given a positive real value M representing a fixed magnitude, and denoting G(s) by z, the points satisfying M = | T ( s ) | = | G ( s ) | | 1 + G ( s ) | = | z | | 1 + z | {\displaystyle M=|T(s)|={\frac {|G(s)|}{|1+G(s)|}}={\frac {|z|}{|1+z|}}} are given by the points z in the G(s)-plane such that the ratio of the distance between z and 0 and the distance between z and -1 is equal to M. The points z satisfying this locus condition are circles of Apollonius, and this locus is known in the context of control systems as M-circles. Given a positive real value N representing a phase angle, the points satisfying N = arg [ G ( s ) 1 + G ( s ) ] = arg [ G ( s ) ] − arg [ 1 + G ( s ) ] = arg [ z ] − arg [ 1 + z ] {\displaystyle N=\arg \left[{\frac {G(s)}{1+G(s)}}\right]=\arg[G(s)]-\arg[1+G(s)]=\arg[z]-\arg[1+z]} are given by the points z in the G(s)-plane such that the angle between -1 and z and the angle between 0 and z is constant. In other words, the angle opposed to the line segment between -1 and 0 must be constant. This implies that the points z satisfying this locus condition are arcs of circles, and this locus is known in the context of control systems as N-circles.
Usage
To use the Hall circles, a plot of M and N circles is done over the Nyquist plot of the open-loop transfer function. The points of the intersection between these graphics give the corresponding value of the closed-loop transfer function. Hall circles are also used with the Nichols plot and in this setting, are also known as Nichols chart. Rather than overlaying directly the Hall circles over the Nichols plot, the points of the circles are transferred to a new coordinate system where the ordinate is given by 20 log 10 ( | G ( s ) | ) {\displaystyle 20\log _{10}(|G(s)|)} and the abscissa is given by arg ( G ( s ) ) {\displaystyle \arg(G(s))} . The advantage of using Nichols chart is that adjusting the gain of the open loop transfer function directly reflects in up and down translation of the Nichols plot in the chart.
See also Nyquist-plot Nichols plot
Notes
References Katsuhiko, Ogata (2002). Modern control engineering (4th ed.). Upper Saddle River, NJ: Prentice Hall. ISBN 0130609072. OCLC 46619221. S., Nise, Norman (2008). Control systems engineering (5th ed.). Hoboken, NJ: Wiley. ISBN 9780471794752. OCLC 154798791.{{cite book}}: CS1 maint: multiple names: authors list (link)
