A homopolar generator is a DC electrical generator comprising an electrically conductive disc or cylinder rotating in a plane perpendicular to a uniform static magnetic field. A potential difference is created between the center of the disc and the rim (or ends of the cylinder) with an electrical polarity that depends on the direction of rotation and the orientation of the field. It is also known as a unipolar generator, acyclic generator, disk dynamo, or Faraday disc. The voltage is typically low, on the order of a few volts in the case of small demonstration models, but large research generators can produce hundreds of volts, and some systems have multiple generators in series to produce an even larger voltage. They are unusual in that they can source tremendous electric current, some more than a million amperes, because the homopolar generator can be made to have very low internal resistance. Also, the homopolar generator is unique in that no other rotary electric machine can produce DC without using rectifiers or commutators.
The Faraday disc
The first homopolar generator was developed by Michael Faraday during his experiments in 1831. It is frequently called the Faraday disc or Faraday wheel in his honor. It was the beginning of modern dynamos — that is, electrical generators which operate using a magnetic field. It was very inefficient and was not used as a practical power source, but it showed the possibility of generating electric power using magnetism, and led the way for commutated direct current dynamos and then alternating current alternators. The Faraday disc was primarily inefficient due to counterflows of current. While current flow was induced directly underneath the magnet, the current would circulate backwards in regions outside the influence of the magnetic field. This counterflow limits the power output to the pickup wires, and induces waste heating of the copper disc. Later homopolar generators would solve this problem by using an array of magnets arranged around the disc perimeter to maintain a steady field around the circumference, and eliminate areas where counterflow could occur.
Homopolar generator development Long after the original Faraday disc had been abandoned as a practical generator, a modified version combining the magnet and disc in a single rotating part (the rotor) was developed. Sometimes the name homopolar generator is reserved for this configuration. One of the earliest patents on the general type of homopolar generators was attained by A. F. Delafield, U.S. patent 278,516. Other early patents for homopolar generators were awarded to S. Z. De Ferranti and C. Batchelor separately. Nikola Tesla was interested in the Faraday disc and conducted work with homopolar generators, and eventually patented an improved version of the device in U.S. patent 406,968. Tesla's "Dynamo Electric Machine" patent describes an arrangement of two parallel discs with separate, parallel shafts, joined like pulleys by a metallic belt. Each disc had a field that was the opposite of the other, so that the flow of current was from the one shaft to the disc edge, across the belt to the other disc edge and to the second shaft. This would have greatly reduced the frictional losses caused by sliding contacts by allowing both electrical pickups to interface with the shafts of the two disks rather than at the shaft and a high-speed rim. Later, patents were awarded to C. P. Steinmetz and E. Thomson for their work with homopolar generators. The Forbes dynamo, developed by the Scottish electrical engineer George Forbes, was in widespread use during the beginning of the 20th century. Much of the development done in homopolar generators was patented by J. E. Noeggerath and R. Eickemeyer.Homopolar generators underwent a renaissance in the 1950s as a source of pulsed power storage. These devices used heavy disks as a form of flywheel to store mechanical energy that could be quickly dumped into an experimental apparatus. An early example of this sort of device was built by Sir Mark Oliphant at the Research School of Physical Sciences and Engineering, Australian National University (ANU). It stored up to 500 megajoules of energy and was used as an extremely high-current source for synchrotron experimentation from 1962 until it was disassembled in 1986. Oliphant's construction was capable of supplying currents of up to 2 megaamperes (MA). Similar devices of even larger size are designed and built by Parker Kinetic Designs (formerly OIME Research & Development) of Austin. They have produced devices for a variety of roles, from powering railguns to linear motors (for space launches) to a variety of weapons designs. Industrial designs of 10 MJ were introduced for a variety of roles, including electrical welding.
Description and operation
Disc-type generator
This device consists of a conducting flywheel rotating in a magnetic field with one electrical contact near the axis and the other near the periphery. It has been used for generating very high currents at low voltages in applications such as welding, electrolysis and railgun research. In pulsed energy applications, the angular momentum of the rotor is used to accumulate energy over a long period and then release it in a short time. In contrast to other types of generators, the output voltage never changes polarity. The charge separation results from the Lorentz force on the free charges in the disk. The motion is azimuthal and the field is axial, so the electromotive force is radial. The electrical contacts are usually made through a "brush" or slip ring, which results in large losses at the low voltages generated. Some of these losses can be reduced by using mercury or other easily liquefied metal or alloy (gallium, NaK) as the "brush", to provide essentially uninterrupted electrical contact. If the magnetic field is provided by a permanent magnet, the generator works regardless of whether the magnet is fixed to the stator or rotates with the disc. Before the discovery of the electron and the Lorentz force law, the phenomenon was inexplicable and was known as the Faraday paradox.
… excerpt ends here. Continue reading the full article.
