A horn antenna or microwave horn is an antenna that consists of a flaring metal waveguide shaped like a horn to direct radio waves in a beam. Horns are widely used as antennas at UHF and microwave frequencies, above 300 MHz. They are used as feed antennas (called feed horns) for larger antenna structures such as parabolic antennas, as standard calibration antennas to measure the gain of other antennas, and as directive antennas for such devices as radar guns, automatic door openers, and microwave radiometers. Their advantages are moderate directivity, broad bandwidth, low losses, and simple construction and adjustment. One of the first horn antennas was constructed in 1897 by Bengali-Indian radio researcher Jagadish Chandra Bose in his pioneering experiments with microwaves. The modern horn antenna was invented independently in 1938 by Wilmer Barrow and G. C. Southworth The development of radar in World War II stimulated horn research to design feed horns for radar antennas. The corrugated horn invented by Kay in 1962 has become widely used as a feed horn for microwave antennas such as satellite dishes and radio telescopes. An advantage of horn antennas is that since they have no resonant elements, they can operate over a wide range of frequencies, a wide bandwidth. The usable bandwidth of horn antennas is typically of the order of 10:1, and can be up to 20:1 (for example allowing it to operate from 1 GHz to 20 GHz). The input impedance is slowly varying over this wide frequency range, allowing low voltage standing wave ratio (VSWR) over the bandwidth. The gain of horn antennas ranges up to 25 dBi, with 10–20 dBi being typical.
Description
A horn antenna is used to transmit radio waves from a waveguide (a metal pipe used to carry radio waves) out into space, or collect radio waves into a waveguide for reception. It typically consists of a short length of rectangular or cylindrical metal tube (the waveguide), closed at one end, flaring into an open-ended conical or pyramidal shaped horn on the other end. The radio waves are usually introduced into the waveguide by a coaxial cable attached to the side, with the central conductor projecting into the waveguide to form a quarter-wave monopole antenna. The waves then radiate out the horn end in a narrow beam. In some equipment the radio waves are conducted between the transmitter or receiver and the antenna by a waveguide; in this case the horn is attached to the end of the waveguide. In outdoor horns, such as the feed horns of satellite dishes, the open mouth of the horn is often covered by a plastic sheet transparent to radio waves, to exclude moisture.
How it works
A horn antenna serves the same function for electromagnetic waves that an acoustical horn does for sound waves in a musical instrument such as a trumpet. It provides a gradual transition structure to match the impedance of a tube to the impedance of free space, enabling the waves from the tube to radiate efficiently into space. If a simple open-ended waveguide is used as an antenna, without the horn, the sudden end of the conductive walls causes an abrupt impedance change at the aperture, from the wave impedance in the waveguide to the impedance of free space, (about 377 Ω). When radio waves travelling through the waveguide hit the opening, this impedance-step reflects a significant fraction of the wave energy back down the guide toward the source, so that not all of the power is radiated. This is similar to the reflection at an open-ended transmission line or a boundary between optical mediums with a low and high index of refraction, like at a glass surface. The reflected waves cause standing waves in the waveguide, increasing the SWR, wasting energy and possibly overheating the transmitter. In addition, the small aperture of the waveguide (less than one wavelength) causes significant diffraction of the waves issuing from it, resulting in a wide radiation pattern without much directivity. To improve these poor characteristics, the ends of the waveguide are flared out to form a horn. The taper of the horn changes the impedance gradually along the horn's length. This acts like an impedance matching transformer, allowing most of the wave energy to radiate out the end of the horn into space, with minimal reflection. The taper functions similarly to a tapered transmission line, or an optical medium with a smoothly varying refractive index. In addition, the wide aperture of the horn projects the waves in a narrow beam. The horn shape that gives minimum reflected power is an exponential taper. Exponential horns are used in special applications that require minimum signal loss, such as satellite antennas and radio telescopes. However conical and pyramidal horns are most widely used, because they have straight sides and are easier to design and fabricate.
Radiation pattern The waves travel down a horn as spherical wavefronts, with their origin at the apex of the horn, a point called the phase center. The pattern of electric and magnetic fields at the aperture plane at the mouth of the horn, which determines the radiation pattern, is a scaled-up reproduction of the fields in the waveguide. Because the wavefronts are spherical, the phase increases smoothly from the edges of the aperture plane to the center, because of the difference in length of the center point and the edge points from the apex point. The difference in phase between the center point and the edges is called the phase error. This phase error, which increases with the flare angle, reduces the gain and increases the beamwidth, giving horns wider beamwidths than similar-sized plane-wave antennas such as parabolic dishes. At the flare angle, the radiation of the beam lobe is down about 20 dB from its maximum value. As the size of a horn (expressed in wavelengths) is increased, the phase error increases, giving the horn a wider radiation pattern. Keeping the beamwidth narrow requires a longer horn (smaller flare angle) to keep the phase error constant. The increasing phase error limits the aperture size of practical horns to about 15 wavelengths; larger apertures would require impractically long horns. This limits the gain of practical horns to about 1000 (30 dBi) and the corresponding minimum beamwidth to about 5–10°.
Types
… excerpt ends here. Continue reading the full article.
