Identification, friend or foe (IFF) is a combat identification system designed for command and control. It uses a transponder that listens for an interrogation signal and then sends a response that identifies the broadcaster. IFF systems usually use radar frequencies, but other electromagnetic frequencies, radio or infrared, may be used. It enables military interrogation systems to identify aircraft, vehicles, or forces as friendly, as opposed to neutral or hostile, and to determine their bearing and range from the interrogator. IFF was first developed during World War II, with the arrival of radar, and several friendly fire incidents. After World War II, IFF technology was adopted by civilian aircraft to assist air traffic control by identifying individual aircraft on radar displays and improving the reliability of tracking information. IFF can only positively identify friendly aircraft or other forces. If an IFF interrogation receives no reply or an invalid reply, the object is not positively identified as foe; friendly forces may not properly reply to IFF for various reasons, such as an equipment malfunction, being near combat but not involved, or being a civilian light general aviation aircraft which may not carry a transponder. IFF is a tool within the broader military action of combat identification (CID), the characterization of objects detected in the field of combat, with sufficient accuracy to support operational decisions. The broadest characterizations are those of friend, enemy, neutral, or unknown. CID can not only reduce friendly fire incidents, but also contributes to overall tactical decision-making. With the successful deployment of radar systems for air defence during World War II, combatants were immediately confronted with the difficulty of distinguishing friendly aircraft from hostile ones; by that time, aircraft were flown at high speed and altitude, making visual identification impossible, and the targets showed up as featureless blips on the radar screen. This led to incidents such as the Battle of Barking Creek, over Britain, and the air attack on the fortress of Koepenick over Germany.
British development
Early concepts
Already before the deployment of their Chain Home radar system (CH), the RAF had considered the problem of IFF. Robert Watson-Watt had filed patents on such systems in 1935 and 1936. By 1938, researchers at Bawdsey Manor began experiments with "reflectors" consisting of dipole antennas tuned to resonate to the primary frequency of the CH radars. When a pulse from the CH transmitter hit the aircraft, the antennas would resonate for a short time, increasing the amount of energy returned to the CH receiver. The antenna was connected to a motorized switch that periodically shorted it out, preventing it from producing a signal. This caused the return on the CH set to periodically lengthen and shorten as the antenna was turned on and off. In practice, the system was found to be too unreliable to use; the return was highly dependent on the direction the aircraft was moving relative to the CH station, and often returned little or no additional signal. It had been suspected from the start this system would be of little use in practice. When that turned out to be the case, the RAF turned to an entirely different system that had also been planned. This consisted of a set of tracking stations using HF/DF radio direction finders. The aircraft voice communications radios were modified to send out a 1 kHz tone for 14 seconds every minute, allowing the stations ample time to measure the aircraft's bearing. Several such stations were assigned to each "sector" of the air defence system, and sent their measurements to a plotting station at sector headquarters, who used triangulation to determine the aircraft's location. Known as "pip-squeak", the system worked, but was labour-intensive and did not display its information directly to the radar operators, the information had to be forwarded to them over the telephone. A system that worked directly with the radar was clearly desirable.
IFF Mark I The first active IFF transponder (transmitter/responder) was the IFF Mark I, which was used experimentally in 1939. This used a regenerative receiver, which fed a small amount of the amplified output back into the input, strongly amplifying even small signals as long as they were of a single frequency (like Morse code, but unlike voice transmissions). They were tuned to the signal from the CH radar (20–30 MHz), amplifying it so strongly that it was broadcast back out the aircraft's antenna. Since the signal was received at the same time as the original reflection of the CH signal, the result was a lengthened "blip" on the CH display which was easily identifiable. In testing, it was found that the unit would often overpower the radar or produce too little signal to be seen, and at the same time, new radars were being introduced using new frequencies.
IFF Mark II
Instead of putting Mark I into production, a new IFF Mark II was introduced in early 1940. Mark II had a series of separate tuners inside tuned to different radar bands that it stepped through using a motorized switch, while an automatic gain control solved the problem of it sending out too much signal. Mark II was technically complete as the war began, but a lack of sets meant it was not available in quantity and only a small number of RAF aircraft carried it by the time of the Battle of Britain. Pip-squeak was kept in operation during this period, but as the Battle ended, IFF Mark II was quickly put into full operation. Pip-squeak was still used for areas over land where CH did not cover, as well as an emergency guidance system.
IFF Mark III
… excerpt ends here. Continue reading the full article.
