Light tubes (also known as solar pipes, tubular skylights or sun tunnels) are structures that transmit or distribute natural or artificial light for the purpose of illumination and are examples of optical waveguides. In their application to daylighting, they are also often called tubular daylighting devices, sun pipes, sun scopes, or daylight pipes. They can be divided into two broad categories: hollow structures that contain the light with reflective surfaces; and transparent solids that contain the light by total internal reflection. Principles of nonimaging optics govern the flow of light through them.
Types
IR light tubes Manufacturing custom designed infrared light pipes, hollow waveguides and homogenizers is non-trivial. This is because these are tubes lined with a highly polished infrared reflective coating of gold, which can be applied thick enough to permit these tubes to be used in highly corrosive atmospheres. Carbon black can be applied to certain parts of light pipes to absorb IR light (see photonics). This is done to limit IR light to only certain areas of the pipe. While most light pipes are produced with a round cross-section, light pipes are not limited to this geometry. Square and hexagonal cross-sections are used in special applications. Hexagonal pipes tend to produce the most homogenized type of IR Light. The pipes do not need to be straight. Bends in the pipe have little effect on efficiency.
Light tube with reflective material
The first commercial reflector systems were patented and marketed in the 1850s by Paul Emile Chappuis in London, using various forms of angled mirror designs. Chappuis Ltd's reflectors were in continuous production until the factory was destroyed in 1943. The concept was rediscovered and patented in 1986 by Solatube International of Australia. This system has been marketed for widespread residential and commercial use. Other daylighting products are on the market under various generic names, such as "SunScope", "solar pipe", "light pipe", "light tube", and "tubular skylight". A tube lined with highly reflective material leads the light rays through a building, starting from an entrance-point located on its roof or one of its outer walls. A light tube is not intended for imaging (in contrast to a periscope, for example); thus image distortions pose no problem and are in many ways encouraged due to the reduction of "directional" light. The entrance point usually comprises a dome (cupola), which has the function of collecting and reflecting as much sunlight as possible into the tube. Many units also have directional "collectors", "reflectors", or even Fresnel lens devices that assist in collecting additional directional light down the tube. In 1994, the Windows and Daylighting Group at Lawrence Berkeley National Laboratory (LBNL) developed a series of horizontal light pipe prototypes to increase daylight illuminance at distances of 4.6-9.1 m, to improve the uniformity of daylight distribution and luminance gradient across the room under variable sun and sky conditions throughout the year. The light pipes were designed to passively transport daylighting through relatively small inlet glazing areas by reflecting sunlight to depths greater than conventional sidelight windows or skylights. A set-up in which a laser cut acrylic panel is arranged to redirect sunlight into a horizontally or vertically orientated mirrored pipe, combined with a light spreading system with a triangular arrangement of laser cut panels that spread the light into the room, was developed at the Queensland University of Technology in Brisbane. In 2003, Veronica Garcia Hansen, Ken Yeang, and Ian Edmonds were awarded the Far East Economic Review Innovation Award in bronze for this development. Light transmission efficiency is greatest if the tube is short and straight. In longer, angled, or flexible tubes, part of the light intensity is lost. To minimize losses, a high reflectivity of the tube lining is crucial; manufacturers claim reflectivities of their materials, in the visible range, of up to almost 99.5 percent. At the end point (the point of use), a diffuser spreads the light into the room. The first full-scale passive horizontal light pipes were built at the Daylight Lab at Texas A&M University, where the annual daylight performance was thoroughly evaluated in a 360° rotating 6 m wide by 10 m deep room. The pipe is coated with a 99.3% specular reflective film and the distribution element at the end of the light pipe consists of a 4.6 m long diffusing radial film with an 87% visible transmittance. The light pipe introduces consistently illuminance levels ranging between 300 and 2,500 lux throughout the year at distances between 7.6 m to 10 m. To further optimize the use of solar light, a heliostat can be installed which tracks the movement of the sun, thereby directing sunlight into the light tube at all times of the day as far as the surroundings' limitations allow, possibly with additional mirrors or other reflective elements that influence the light path. The heliostat can be set to capture moonlight at night.
… excerpt ends here. Continue reading the full article.
