A marine steam engine is a steam engine that is used to power a ship or boat. This article deals mainly with marine steam engines of the reciprocating type, which were in use from the inception of the steamboat in the early 19th century to their last years of large-scale manufacture during World War II. Reciprocating steam engines were progressively replaced in marine applications during the 20th century by steam turbines and marine diesel engines.
History The first commercially successful steam engine was developed by Thomas Newcomen in 1712. The steam engine improvements brought forth by James Watt in the later half of the 18th century greatly improved steam engine efficiency and allowed more compact engine arrangements. Successful adaptation of the steam engine to marine applications in England would have to wait until almost a century after Newcomen, when Scottish engineer William Symington built the world's "first practical steamboat", the Charlotte Dundas, in 1802. Rivaling inventors James Rumsey and John Fitch were the first to build steamboats in the United States. Rumsey exhibited his steamboat design in 1787 on the Potomac River; however, Fitch won the rivalry in 1790 after his successful test resulted in a passenger service on the Delaware River. In 1807, the American Robert Fulton built the world's first commercially successful steamboat, simply known as the North River Steamboat, and powered by a Watt engine. Following Fulton's success, the steamboat technology developed rapidly on both sides of the Atlantic. Steamboats initially had a short range and were not particularly seaworthy due to their weight, low power, and tendency to break down, but they were employed successfully along rivers and canals, and for short journeys along the coast. The first successful transatlantic crossing by a steamship occurred in 1819 when Savannah sailed from Savannah, Georgia to Liverpool, England. The first steamship to make regular transatlantic crossings was the sidewheel steamer Great Western in 1838. As the 19th century progressed, marine steam engines and steamship technology developed alongside each other. Paddle propulsion gradually gave way to the screw propeller, and the introduction of iron and later steel hulls to replace the traditional wooden hull allowed ships to grow ever larger, necessitating steam power plants that were increasingly complex and powerful.
Types of marine steam engine A wide variety of reciprocating marine steam engines were developed over the course of the 19th century. The two main methods of classifying such engines are by connection mechanism and cylinder technology. Most early marine engines had the same cylinder technology (simple expansion, see below) but a number of different methods of supplying power to the crankshaft (i.e. connection mechanism) were in use. Thus, early marine engines are classified mostly according to their connection mechanism. Some common connection mechanisms were side-lever, steeple, walking beam and direct-acting (see following sections). However, steam engines can also be classified according to cylinder technology (simple-expansion, compound, annular etc.). One can therefore find examples of engines classified under both methods. An engine can be a compound walking beam type, compound being the cylinder technology, and walking beam being the connection method. Over time, as most engines became direct-acting but cylinder technologies grew more complex, engines began to be classified solely according to cylinder technology. More commonly encountered marine steam engine types are listed in the following sections. Note that not all these terms are exclusive to marine applications.
Engines classified by connection mechanism
Side-lever The side-lever engine was the first type of steam engine widely adopted for marine use in Europe. In the early years of steam navigation (from c. 1815), the side-lever was the most common type of marine engine for inland waterway and coastal service in Europe, and it remained for many years the preferred engine for oceangoing service on both sides of the Atlantic. The side-lever was an adaptation of the earliest form of steam engine, the beam engine. The typical side-lever engine had a pair of heavy horizontal iron beams, known as side-levers, each secured in the centre by a pin near the base of the engine, allowing the levers to pivot through a limited arc. The engine cylinder stood vertically between this pair of levers at one end, with the piston rod attached to a horizontal crosshead above, from each end of which a vertical rod, known as a side-rod, extended down each side of the cylinder to connect to the end of the side-lever on the same side. The far ends of the two side-levers were connected to one another by a horizontal crosstail, from which extended a single, common connecting rod which operated the crankshaft as the levers rocked up and down around the central pin. The main disadvantage of the side-lever engine was that it was large and heavy. For inland waterway and coastal service, lighter and more efficient designs soon replaced it. It remained the dominant engine type for oceangoing service through much of the first half of the 19th century however, due to its relatively low centre of gravity, which gave ships more stability in heavy seas. It was also a common early engine type for warships, since its relatively low height made it less susceptible to battle damage. From the first Royal Navy steam vessel in 1820 until 1840, 70 steam vessels entered service, the majority with side-lever engines, using boilers set to 4psi maximum pressure. The low steam pressures dictated the large cylinder sizes for the side-lever engines, though the effective pressure on the piston was the difference between the boiler pressure and the vacuum in the condenser. The side-lever engine was a paddlewheel engine and was not suitable for driving screw propellers. The last ship built for transatlantic service that had a side-lever engine was the Cunard Line's paddle steamer RMS Scotia, considered an anachronism when it entered service in 1862.
Grasshopper
… excerpt ends here. Continue reading the full article.
