Myocardial perfusion imaging or scanning (also referred to as MPI or MPS) is a nuclear medicine procedure that illustrates the function of the heart muscle (myocardium). It evaluates many heart conditions, such as coronary artery disease (CAD), hypertrophic cardiomyopathy and heart wall motion abnormalities. It can also detect regions of myocardial infarction by showing areas of decreased resting perfusion. The function of the myocardium is also evaluated by calculating the left ventricular ejection fraction (LVEF) of the heart. This scan is done in conjunction with a cardiac stress test. The diagnostic information is generated by provoking controlled regional ischemia in the heart with variable perfusion. Planar techniques, such as conventional scintigraphy, are rarely used. Rather, single-photon emission computed tomography (SPECT) is more common in the US. With multihead SPECT systems, imaging can often be completed in less than 10 minutes. With SPECT, inferior and posterior abnormalities and small areas of infarction can be identified, as well as the occluded blood vessels and the mass of infarcted and viable myocardium. The usual isotopes for such studies are either thallium-201 or technetium-99m.
History The history of nuclear cardiology began in 1927 when Dr. Herrmann Blumgart developed the first method for measuring cardiac strength by injecting subjects with a radioactive compound known as Radium C (214Bi). The substance was injected into the venous system and travelled through the right heart into the lungs, then into the left heart and out into the arterial system where it was then detected through a Wilson chamber. The Wilson chamber represented a primitive scintillation counter which could measure radioactivity. Measured over time, this sequential acquisition of radioactivity produced what was known as "circulation time". The longer the "circulation time", the weaker the heart. Blumgart's emphasis was twofold. First, radioactive substances could be used to determine cardiac physiology (function) and should be done so with the least amount of radioactivity necessary to do so. Secondly, to accomplish this task, one needs to obtain multiple counts over time. For decades no substantial work was done, until 1959. Dr. Richard Gorlin's work on "resting" studies of the heart and nitroglycerin emphasized several points. First, like Blumgart, he emphasized that evaluation of cardiac function required multiple measurements of change over time and these measurements must be performed under same state conditions, without changing the function of the heart in between measurements. If one is to evaluate ischemia (reductions in coronary blood flow resulting from coronary artery disease) then individuals must be studied under "stress" conditions and comparisons require "stress-stress" comparisons. Similarly, if tissue damage (heart attack, myocardial infarction, cardiac stunning or hibernation) is to be determined, this is done under "resting" conditions. Rest-stress comparisons do not yield adequate determination of either ischemia or infarction. By 1963, Dr. William Bruce, aware of the tendency of people with coronary artery disease to experience angina (cardiac chest discomfort) during exercise, developed the first standardized method of "stressing" the heart, where serial measurements of changes in blood pressure, heart rate and electrocardiographic (ECG/EKG) changes could be measured under "stress-stress" conditions. By 1965 Dr. William Love demonstrated that the cumbersome cloud chamber could be replaced by a Geiger counter, which was more practical to use. However, Love had expressed the same concern as many of his colleagues, namely that there were no suitable radioisotopes available for human use in the clinical setting.
Use of thallium-201 By the mid-1970s, scientists and clinicians alike began using thallium-201 as the radioisotope of choice for human studies. Individuals could be placed on a treadmill and be "stressed" by the "Bruce protocol" and when near peak performance, could be injected with thallium-201. The isotope required exercise for an additional minute to enhance circulation of the isotope. Using nuclear cameras of the day and given the limitations of Tl-201, the first "stress" image could not be taken until 1 hour after "stress". In keeping with the concept of comparison images, the second "stress" image was taken 4 hours after "stress" and compared with the first. The movement of Tl-201 reflected differences in tissue delivery (blood flow) and function (mitochondrial activity). The relatively long half-life of Tl-201 (73 hours) forced doctors to use relatively small (74–111 MBq or 2–3 mCi) doses of Tl-201, albeit with relatively large dose exposure and tissue effects (20 mSv). The poor quality images resulted in the search for isotopes which would produce better results.
The introduction of technetium-99m isotopes By the late 1980s, two different compounds containing technetium-99m were introduced: teboroxime and sestamibi. The utilization of Tc-99m would allow higher doses (up to 1,100 MBq or 30 mCi) due to the shorter physical (6 hours) half-life of Tc-99m. This would result in more decay, more scintillation and more information for the nuclear cameras to measure and turn into better pictures for the clinician to interpret.
Positron emission tomography in myocardial perfusion imaging The use of positron emission tomography (PET) has been limited due to the shorter half-life of the radionuclides used and the need for in-house production. While not as widely available, PET is increasingly used for myocardial perfusion imaging (MPI). Recent guidelines states that PET is the preferred functional imaging test in patients with chronic coronary syndromes and suspected CAD. The main benefit of performing PET instead of SPECT is absolute quantification of myocardial blood flow (MBF) in terms of ml/g/min rather than assessing relative perfusion defects. PET also provides higher image quality and better tracer properties which allows for more detailed diagnostics, resulting in higher diagnostic accuracy and prognostics implications. The available tracers in PET MPI is oxygen-15 water, rubidium-82, nitrogen-13 ammonia, and the newly introduced fluorine-18 flurpiridaz.
… excerpt ends here. Continue reading the full article.
