A PIN diode is a diode with a wide, undoped intrinsic semiconductor region between a p-type semiconductor and an n-type semiconductor region. The p-type and n-type regions are typically heavily doped because they are used for ohmic contacts. The wide intrinsic region is in contrast to an ordinary p–n diode. The wide intrinsic region makes the PIN diode an inferior rectifier (one typical function of a diode), but it makes it suitable for attenuators, fast switches, photodetectors, and high-voltage power electronics applications. The PIN photodiode was invented by Jun-Ichi Nishizawa and his colleagues in 1950. It is a semiconductor device.
Operation A PIN diode operates under what is known as high-level injection. In other words, the intrinsic "i" region is flooded with charge carriers from the "p" and "n" regions. Its function can be likened to filling up a water bucket with a hole on the side. Once the water reaches the hole's level it will begin to pour out. Similarly, the diode will conduct current once the flooded electrons and holes reach an equilibrium point, where the number of electrons is equal to the number of holes in the intrinsic region. When the diode is forward biased, the injected carrier concentration is typically several orders of magnitude higher than the intrinsic carrier concentration. Due to this high level injection, which in turn is due to the depletion process, the electric field extends deeply (almost the entire length) into the region. This electric field helps in speeding up of the transport of charge carriers from the P to the N region, which results in faster operation of the diode, making it a suitable device for high-frequency operation.
Characteristics The PIN diode obeys the standard diode equation for low-frequency signals. At higher frequencies, the diode looks like an almost perfect (very linear, even for large signals) resistor. The P-I-N diode has a relatively large stored charge adrift in a thick intrinsic region. At a low-enough frequency, the stored charge can be fully swept and the diode turns off. At higher frequencies, there is not enough time to sweep the charge from the drift region, so the diode never turns off. The time required to sweep the stored charge from a diode junction is its reverse recovery time, and it is relatively long in a PIN diode. For a given semiconductor material, on-state impedance, and minimum usable RF frequency, the reverse recovery time is fixed. This property can be exploited; one variety of P-I-N diode, the step recovery diode, exploits the abrupt impedance change at the end of the reverse recovery to create a narrow impulse waveform useful for frequency multiplication with high multiples. The high-frequency resistance is inversely proportional to the DC bias current through the diode. A PIN diode, suitably biased, therefore acts as a variable resistor. This high-frequency resistance may vary over a wide range (from 0.1 Ω to 10 kΩ in some cases; the useful range is smaller, though). The wide intrinsic region also means the diode will have a low capacitance when reverse-biased. In a PIN diode the depletion region exists almost completely within the intrinsic region. This depletion region is much larger than in a PN diode and almost constant-size, independent of the reverse bias applied to the diode. This increases the volume where electron-hole pairs can be generated by an incident photon. Some photodetector devices, such as PIN photodiodes and phototransistors (in which the base-collector junction is a PIN diode), use a PIN junction in their construction. The diode design has some design trade-offs. Increasing the cross-section area of the intrinsic region increases its stored charge reducing its RF on-state resistance while also increasing reverse bias capacitance and increasing the drive current required to remove the charge during a fixed switching time, with no effect on the minimum time required to sweep the charge from the I region. Increasing the thickness of the intrinsic region increases the total stored charge, decreases the minimum RF frequency, and decreases the reverse-bias capacitance, but doesn't decrease the forward-bias RF resistance and increases the minimum time required to sweep the drift charge and transition from low to high RF resistance. Diodes are sold commercially in a variety of geometries for specific RF bands and uses.
Applications PIN diodes are useful as RF switches, attenuators, photodetectors, and phase shifters.
RF and microwave switches
Under zero- or reverse-bias (the "off" state), a PIN diode has a low capacitance. The low capacitance will not pass much of an RF signal. Under a forward bias of 1 mA (the "on" state), a typical PIN diode will have an RF resistance of about 1 ohm, making it a good conductor of RF. Consequently, the PIN diode makes a good RF switch. Although RF relays can be used as switches, they switch relatively slowly (on the order of tens of milliseconds). A PIN diode switch can switch much more quickly (e.g., 1 microsecond), although at lower RF frequencies it isn't reasonable to expect switching times in the same order of magnitude as the RF period. For example, the capacitance of an "off"-state discrete PIN diode might be 1 pF. At 320 MHz, the capacitive reactance of 1 pF is 497 ohms:
… excerpt ends here. Continue reading the full article.
