A power strip (also known as a multi-socket, power board and many other variations) is a block of electrical sockets that attaches to the end of a flexible cable (typically with a mains plug on the other end), allowing multiple electrical devices to be powered from a single electrical socket. Power strips are often used when many electrical devices are in proximity, such as for audio, video, computer systems, appliances, power tools, and lighting. Power strips often include a circuit breaker to interrupt the electric current in case of an overload or a short circuit. Some power strips provide protection against electrical power surges. Typical housing styles include strip, rack-mount, under-monitor and direct plug-in.
Control
Some power strips include a master switch to turn all devices on and off. This can be used with simple devices, such as lights, but not with most computers, which must use shutdown commands from the software first. Computers may have open files, which may be damaged if the power is simply turned off. Some power strips have individually switched outlets. "Master/slave" strips can detect one "master" device being turned off (such as the PC itself in a computer setup, or a TV in a home theatre) and turn everything else on or off accordingly. Remote control strips are used in data centers, to allow computer systems or other devices to be remotely restarted, often over the Internet (although this leaves them vulnerable to outside attacks).
Indication Many power strips have a neon or LED indicator light or one per output socket to show when power is on. Better-quality surge-protected strips have additional lights to indicate the status of the surge protection system, however these are not always reliable as an indicator.
Energy-Saving Features and Standby Power Some power strips have energy-saving features, which switch off the strip if appliances go into standby mode. Using a sensor circuit, they detect if the level of power through the socket is in standby mode (less than 30 watts), and if so they will turn off that socket. This reduces the consumption of standby power used by computer peripherals and other equipment when not in use, saving money and energy Some more-sophisticated power strips have a master and slave socket arrangement, and when the "master" socket detects standby mode in the attached appliance's current it turns off the whole strip. However, there can be problems detecting standby power in appliances that use more power in standby mode (such as plasma televisions) as they will always appear to the power strip to be switched on. When using a master–slave power strip, one way to avoid such problems is to plug an appliance with a lower standby wattage (such as a DVD player) into the master socket, using it as the master control instead. A different power strip design intended to save energy uses a passive infrared (PIR) or ultrasonic sound detector to determine if a person is nearby. If the sensors don't detect any motion for a preset period of time, the strip shuts off several outlets, while leaving one outlet on for devices that should not be powered off. These so-called "smart power strips" are intended to be installed in offices, to shut down equipment when the office is unoccupied. It is recommended that appliances that need a controlled shutdown sequence (such as many ink-jet printers) not be plugged into a slave socket on such a strip as it can damage them if they are switched off incorrectly (for example the inkjet printer may not have capped the print head in time, and consequently the ink will dry and clog the print head.) Within Europe, power strips with energy-saving features are within the scope of the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC and require a CE mark.
Socket Arrangement
In some countries where multiple socket types are in use, a single power strip can have two or more kinds of sockets. Socket arrangement varies considerably, but for physical access reasons there are rarely more than two rows. In Europe, power strips without surge suppression are normally single row, but models with surge suppression are supplied both in single and double row configurations.
If sockets on a power strip are grouped closely together, a cable with a large "wall wart" transformer at its end may cover up multiple sockets. Various designs address this problem, some by simply increasing the spacing between outlets. Other designs include receptacles which rotate in their housing, or multiple short receptacle cords feeding from a central hub. A simple DIY method for adapting problematic power strips arrangements to large "wall warts" is to use a three-way socket adapter to extend the socket above its neighbors, providing the required clearance.
Surge Protection and Filtering
… excerpt ends here. Continue reading the full article.
