Slope mass rating (SMR) is a rock mass classification scheme developed by Manuel Romana to describe the strength of an individual rock outcrop or slope. The system is founded upon the more widely used RMR scheme, which is modified with quantitative guidelines to the rate the influence of adverse joint orientations (e.g. joints dipping steeply out of the slope). Slope mass rating has been widely used worldwide. It has been included in the technical regulations of some countries as a classification system by itself or as a quality index for rocky slopes (e.g., India, Serbia, Italy). It has also been used in more than 50 countries across five continents, especially in Asia (e.g., China and India), where its use is very common.
Definition Rock mass classification schemes are designed to account for a number of factors influencing the strength and deformability of a rock mass (e.g. joint orientations, fracture density, intact strength), and may be used to quantify the competence of an outcrop or particular geologic material. Scores typically range from 0 to 100, with 100 being the most competent rock mass. The term rock mass incorporates the influence of both intact material and discontinuities on the overall strength and behavior of a discontinuous rock medium. While it is relatively straightforward to test the mechanical properties of either intact rock or joints individually, describing their interaction is difficult and several empirical rating schemes (such as RMR and SMR) are available for this purpose.
SMR index calculation SMR uses the same first five scoring categories as RMR:
Uniaxial compressive strength of intact rock, Rock Quality Designation (or RQD), Joint spacing, Joint condition (the sum of five sub-scores), and Groundwater conditions. The final sixth category is a rating adjustment or penalization for adverse joint orientations, which is particularly important for evaluating the competence of a rock slope. SMR provides quantitative guidelines to evaluate this rating penalization in the form of four sub-categories, three that describe the relative rock slope and joint set geometries and a fourth which accounts for the method of slope excavation. SMR addresses both planar sliding and toppling failure modes, no additional consideration was made originally for sliding on multiple joint planes. However, Anbalagan et al. adapted the original classification for wedge failure mode. The final SMR rating is obtained by means of next expression:
S M R = R M R b + F 1 × F 2 × F 3 + F 4 {\displaystyle SMR=RMR_{b}+F_{1}\times F_{2}\times F_{3}+F_{4}}
where:
RMRb is the RMR index resulting from Bieniawski's Rock Mass Classification without any correction. F1 depends on the parallelism between discontinuity, αj (or the intersection line, αi, in the case of wedge failure) and slope dip direction. F2 depends on the discontinuity dip (βj) in the case of planar failure and the plunge, βi of the intersection line in wedge failure. As regards toppling failure, this parameter takes the value 1.0. This parameter is related to the probability of discontinuity shear strength. F3 depends on the relationship between slope (βs) and discontinuity (βj) dips (toppling or planar failure cases) or the immersion line dip (βi) (wedge failure case). This parameter retains the Bieniawski adjustment factors that vary from 0 to −60 points and express the probability of discontinuity outcropping on the slope face for planar and wedge failure. F4 is a correction factor that depends on the excavation method used. Although SMR is worldwide used, sometimes some misinterpretations and imprecisions are made when applied. Most of the observed inaccuracies are related to the calculation of the ancillary angular relationships between dips and dip directions of the discontinuities and the slope required to determine F1, F2 and F3 factors. A comprehensive definition of these angular relationships can be found in.
SMR index modifications Continuous SMR (C-SMR) Tomás et al. proposed alternative continuous functions for the computation of F1, F2 and F3 correction parameters. These functions show maximum absolute differences with discrete functions lower than 7 points and significantly reduce subjective interpretations. Moreover, the proposed functions for SMR correction factors calculus reduce doubts about what score to assign to values near the border of the discrete classification. The proposed F1 continuous function that best fits discrete values is:
F 1 = 16 25 − 3 500 arctan ( 1 10 ( | A | − 17 ) ) {\displaystyle F_{1}={\frac {16}{25}}-{\frac {3}{500}}\arctan \left({\frac {1}{10}}\left(|A|-17\right)\right)}
where parameter A is the angle formed between the discontinuity and the slope strikes for planar and toppling failures modes and the angle formed between the intersection of the two discontinuities (the plunge direction) and the dip direction of the slope for wedge failure. Arctangent function is expressed in degrees.
… excerpt ends here. Continue reading the full article.
