A taxiway is a path for aircraft at an airport connecting runways with aprons, hangars, terminals and other facilities. They mostly have a hard surface such as asphalt or concrete, although smaller general aviation airports sometimes use gravel or grass. Most airports do not have a specific speed limit for taxiing (though some do). There is a general rule on safe speed based on obstacles. Operators and aircraft manufacturers might have limits. Typical taxi speeds are 20–30 kn (37–56 km/h; 23–35 mph).
High-speed exit Busy airports typically construct high-speed or rapid-exit taxiways to allow aircraft to leave the runway at higher speeds. This allows the aircraft to vacate the runway more quickly, permitting another to land or take off in a shorter interval of time. This is accomplished by reducing the angle the exiting taxiway intercepts the runway at to 30 degrees, instead of 90 degrees, thus increasing the speed at which the aircraft can exit the runway onto the taxiway.
Markings Normal Centerline A single continuous yellow line, 15 to 30 centimetres (6 to 12 in) in width. Enhanced Centerline The enhanced taxiway center line marking consists of a parallel line of yellow dashes on either side of the taxiway centerline. Taxiway centerlines are enhanced for 150 feet (46 m) before a runway holding position marking. The enhanced taxiway centerline is standard at all FAR Part 139 certified airports in the US. Taxiway Edge Markings Used to define the edge of the taxiway when the edge does not correspond with the edge of the pavement. Continuous markings consist of a continuous double yellow line, with each line being at least 15 centimetres (6 in) in width, spaced 15 centimetres (6 in) apart. They divide the taxiway edge from the shoulder or some other abutting paved surface not intended for use by aircraft. Dashed markings define the edge of a taxiway on a paved surface where the adjoining pavement to the taxiway edge is intended for use by aircraft, e.g., an apron. These markings consist of a broken double yellow line, with each line being at least 15 centimetres (6 in) in width, spaced 15 centimetres (6 in) apart (edge to edge). These lines are 15 feet (4.6 m) in length with 25-foot (7.6 m) gaps. Taxi Shoulder Markings Taxiways, holding bays, and aprons are sometimes provided with paved shoulders to prevent blast and water erosion. Shoulders are not intended for use by aircraft, and may be unable to carry the aircraft load. Taxiway shoulder markings are yellow lines perpendicular to the taxiway edge, from taxiway edge to pavement edge, about 3 metres. Surface Painted Taxiway Direction Signs Yellow background with a black inscription, provided when it is not possible to provide taxiway direction signs at intersections, or when necessary to supplement such signs. These markings are located on either side of the taxiway. Surface Painted Location Signs Black background with a yellow inscription and yellow and black border. Where necessary, these markings supplement location signs located alongside the taxiway and assist the pilot in confirming the designation of the taxiway on which the aircraft is located. These markings are located on the right side of the centerline. Geographic Position Markings These markings are located at points along low visibility taxi routes (when Runway visual range is below 1,200 feet (370 m)). They are positioned to the left of the taxiway centerline in the direction of taxiing. Black inscription centered on pink circle with black inner and white outer ring. If the pavement is a light colour then the border is white with a black outer ring. Runway Holding Position Markings These show where an aircraft should stop when approaching a runway from a taxiway. They consist of four yellow lines, two solid and two dashed, spaced six or twelve inches (15 or 30 cm) apart, and extending across the width of the taxiway or runway. The solid lines are always on the side where the aircraft is to hold. There are three locations where runway holding position markings are encountered: Runway holding position markings on taxiways; runway holding position markings on runways; taxiways located in runway approach areas. Holding Position Markings for Instrument Landing System (ILS) These consist of two yellow solid lines spaced two feet (61 cm) apart connected by pairs of solid lines spaced ten feet (3.0 metres) apart extending across the width of the taxiway. Holding Position Markings for Taxiway/Taxiway Intersections These consist of a single dashed line extending across the width of the taxiway. Surface Painted Holding Position Signs Red background signs with a white inscription to supplement the signs located at the holding position. The taxiways are given alphanumeric identification. These taxiway IDs are shown on black and yellow signboards along the taxiways.
Signs
Airport guidance signs provide direction and information to taxiing aircraft and airport vehicles. Smaller airports may have few or no signs, relying instead on airport diagrams and charts.
There are two classes of signage at airports, with several types of each:
Operational guidance signs Location signs – yellow on black background. Identifies the runway or taxiway the aircraft is currently on or is entering. Direction/Runway exit signs – black on yellow. Identifies the intersecting taxiways the aircraft is approaching, with an arrow indicating the direction to turn. Destination signs – black on yellow, similar to the direction signs. They indicate a destination at the airport and always have an arrow showing the direction of the taxi route to that destination. When the inscription for two or more destinations having a common taxi route are placed on a sign, the destinations are separated by an interpunct (•) and only one arrow is used. Stop Bar signs – white on blue background. The designation consists of the letter S followed by designation of the taxiway on which the Stop Bar is positioned. This sign is not standard. Other – many airports use conventional traffic signs such as stop and yield signs throughout the airport.
Mandatory instruction signs Mandatory instruction signs are white on red. They show entrances to runways or critical areas. Vehicles and aircraft are required to stop at these signs until the control tower gives clearance to proceed.
… excerpt ends here. Continue reading the full article.
